One solution for grid-tie backup and off-grid solar (230 VAC)
Conext XW+ is an adaptable single-phase and three-phase hybrid inverter with grid-tie functionality and dual AC power inputs. Available solar charge controllers, monitoring, and automated generator control modules enable further adaptability. From a single Conext XW+ unit to clusters up to 102 kW, the Conext XW+ is a scalable system that allows for the integration of solar capacity as required. Adaptable and scalable, the Schneider Electric Conext XW+ system is the one solution for grid-interactive and off-grid, residential and commercial, solar and backup power applications.
⦁ Output power continuous at 25°C: 6800W
⦁ Output power continuous at 40°C: 6000W
⦁ Nominal battery Voltage: 48V
⦁ Input DC voltage range: 40 to 64VDC
⦁ Ouput volatge: 230Vac 50Hz/60Hz
⦁ Peak efficiency: 95.8%
⦁ Max output Charge current (DC): 140A
⦁ Max AC Input current: 29.6 A
⦁ Max Input DC current: 180 A
⦁ Transfer time: 8ms
⦁ Idle power consumption: <7W
⦁ Supported battery types: Flooded, AGM, GEL, LiON, Custom
⦁ Operation temp range: -25°C to 70°C
⦁ Dimensions (mm) (LxBxW): 711x572x394
⦁ Weight: 55.2 kg
⦁ Ingress protection: IP20 Indoor only
⦁ Off-grid AC coupling: Frequency control
12/24/36/48V auto work
Advanced MPPT technology
Several seconds tracking speed
High Tracking efficiency of 99%
Peak conversion efficiency of 98%
New 60A eTracer ET6415BND MPPT Solar Charge Controller, 60amps 12V 24V 36V 48V EP Solar Battery Charge Controller Regulators
Maximum Power Point Tracking technology for increased PV power output efficiency.
• Continuous charging current up to 100ADC and high input voltage up to 240VDC (Voc).
• Compatible with 12, 24 or 48V battery systems with automatic detection of system voltage
Single controller supports large PV array up to 6600W.
• Peak conversion efficiency is higher than 99% (PV In to DC Out).
The Conext MPPT 60 150 is a photovoltaic (PV) charge controller that tracks the maximum power point of a PV array to deliver the maximum available current for charging batteries. When charging, the MPPT 60 150 regulates battery voltage and output current based on the amount of energy available from the PV array and state-of-charge of the battery.
Remote Display for C35,C40,C60,15mcable
CM/R-50 Xantrex Remote Display For Solar Charge Controller
Digital Meter Mounts Designed for use with C Series Charge Controllers, this digital meter mounts onto the front of a charge controller, or as a remote, it can be installed up to 100 ft (31 m) away. It displays volts, amps, and resettable cumulative amp hours for a solar array, DC loads, or diversion loads, depending on application. The CM/R comes with 50 ft (15 m) or 100 ft (31 m) communication cable for remote installation.
This is an electronic device or circuit that maintains an output voltage to be consistent to its load current. This is necessary because the voltage delivered to your home and mine may sometimes fluctuate which can cause serious damages to your appliance; if not completely destroying it. This AVR has a servomechanism that hunts the accurate voltage when surges happen in order to maintain the needed voltage level that ultimately protects your appliance.
LCD Display, 10KVA, Single Phase, Input voltage: AC170V - AC250V, Output voltage: AC220V +/- 3%, Efficiency: >90%, Frequency: 50Hz, Adjust time: Within 1 second against 10%input voltage variation, Delay time: 5 seconds/255 seconds choice
Supports inductive loads